The Fluke Philips PM2811 is a Single Output DC Power Supply with the following specifications:

• OUTPUT module 30 V - 10 A - 60 W
  
  
  
  • Output Voltage range 0 to 30 V
    
  • Output Current range 0 to 10 A
    
  • Output Power 60 W
    
  • Overvoltage protection range 2 to 32 V
  
  
• Accuracy (at calibration temperature)
  
  
  
  • Output Voltage ± 0.04 % of setting + 10 mV
    
  • Output Current ± 0.1 % of setting + 50 mA
    
  • Over Voltage Protection ± 0.5 % of setting + 150 mV
  
  
• Temperature coefficient
  
  
  
  • Output Voltage (0.016 % of setting + 2 mV)/K
    
  • Output Current (0.05 % of setting + 2 mA)/K
  
  
• Long term drift (in an 8 hour period)
  
  
  
  • Output Voltage 0.04 % of setting + 5 mV
    
  • Output Current 0.05 % of setting + 10 mA
  
  
• Programming Resolution (12bit)
  
  
  
  • Output Voltage 7.5 mV/LSB
    
  • Output Current 2.5 mA/LSB
    
  • Over Voltage Protection 7.5 mV/LSB
  
  
• Source Effect (for any line voltage change within rating)
  
  
  
  • Voltage ± (0.01 % of setting + 2 mV)
    
  • Current ± (0.02 % of setting + 2 mA)
  
  
• Load Effect (load change 10 % to 90 % or 90 % to 10 % full load)
  
  
  
  • Constant Voltage ± (0.01 % of setting + 5 mV)
    
  • Constant Current ± (0.02 % of setting + 5 mA)
  
  
• Load cross regulation Negligible for both voltage and current
  
• Output Noise (PARD)
  
  
  
  • Constant Voltage pp/rms 15 mV/3 mV
    
  • Constant Current rms 10 mA
    
  • Switching Frequency approx. 20 kHz approx.
  
  
• READBACK ACCURACY:(referred to the output terminals)
  
• Accuracy (at calibration temperature)
  
  
  
  • Voltage ± (0.05 % + 25 mV)
    
  • Current ± (0.1 % + 30 mA)
  
  
• Measuring Resolution (12 bit)
  
  
  
  • Voltage resolution to interface 7.5 mV
    
  • Current resolution to interface 2.5 mA
    
  • Voltage resolution to display 10 mV
    
  • Current resolution to display 10 mA
    
  • Max. Current at Reverse voltage 10 A
    
  • REMOTE SENSE > 0.25 Volt drop per lead (at open sense connections, the output voltage will not be more than 3 V above the programmed value)
    
  • DYNAMIC OPERATION ÆI=1 A between 1 and 10A between 0.5 and 5A between 1 and 10A
    
    
    
    • Settling band ± 50 mV
      
    • dI/dt < 1 A/μs
      
    • Overshoot < 150 mV
      
    • Recovery time < 1 ms
    
    
  • Programming response (measured with resistive load)
    
  • Up (0 V to max. output) 100 ms @ 2 A
    
  • Up (0 V to max. output) 50 ms @ (no load)
    
  • Down(max. output to 1 V) 100 ms @ 2 A
    
  • Down (max. output to 1 V) 50 ms @ (no load)
  
  
• Reprogramming delay
  
  
  
  • Range 50 ms to 60 s
    
  • Resolution 1 ms
    
  • Default 50 ms
    
  • Step Interval time up to 60 s